Flange Nuts
Hex nuts with an integral bearing flange, optionally serrated, that spread load and resist loosening.
Materials: stainless, carbon, alloy steel and more, subject to enquiry
DIN 6923
View ProductHex Nuts
Hexagon nuts in standard and heavy series for general and pressure bolting.
Product Overview
Hexagon nuts in standard and heavy series for general and pressure bolting.
A nut is an internally threaded fastener that mates with a bolt or stud to develop clamp load. It must be matched to the bolt by thread size, pitch, and property class or grade so that the assembly fails in the bolt, not by thread stripping.
- Matched to bolt and stud property classes
- Prevailing torque options resist vibration loosening
- Standard and heavy series available
Technical Specifications
| Product Name | Hex Nuts |
| Product Type | Nuts |
| Material | Stainless steel, carbon steel, alloy steel, duplex, super duplex, nickel alloys, brass, titanium, high tensile (subject to enquiry) |
| Grade | 304, 316, 2H, Gr 8, 8, 10, 12, A2-70, A4-70 |
| Size Range | Available as per customer specification |
| Head / Drive | Hexagon, internal thread |
| Thread Type | Metric coarse/fine (ISO 261, 6H) or UNC/UNF (ASME B1.1, 2B) |
| Manufacturing / Dimensional Standard | ASME B18.2.2, ASTM A194 2H/8/8M, ASTM A563, ISO 4032/4033, DIN 934, ISO 898-2 (applicable standard confirmed against your order) |
| Finish / Coating | Plain, zinc plated, hot dip galvanized, black oxide, passivated, electro galvanized, nickel plated, or customer specified |
| Mechanical Properties | Per material grade and standard; see table below |
| Testing / Inspection | Dimensional, visual, thread, mechanical and chemical checks as agreed with the order |
| Certification | Material Test Certificate on request; EN 10204 3.1 where requested |
Standards
Standards commonly associated with Hex Nuts: ASME B18.2.2, ASTM A194 2H/8/8M, ASTM A563, ISO 4032/4033, DIN 934, ISO 898-2. The governing standard is confirmed against your purchase specification; not every standard is stocked or supplied in every size or grade.
Dimensions
ISO 4032 reference dimensions (mm). Values are nominal references; confirm against the current standard.
| Thread | Pitch (coarse) | Across flats s (mm) | Height m (mm) |
|---|---|---|---|
| M6 | 1.0 | 10 | 5.2 |
| M8 | 1.25 | 13 | 6.8 |
| M10 | 1.5 | 16 | 8.4 |
| M12 | 1.75 | 18 | 10.8 |
| M16 | 2.0 | 24 | 14.8 |
| M20 | 2.5 | 30 | 18.0 |
| M24 | 3.0 | 36 | 21.5 |
Dimensions are manufactured according to the applicable dimensional standard and customer requirements.
Materials and Grades
| Material | Typical grades | Standards |
|---|---|---|
| Stainless Steel | 304, 304L, 316, 316L, 321 | ASTM F593, F594, A193 B8/B8M/B6, A194 Gr 8/8M, A276, ISO 3506-1/-2 |
| Carbon Steel | Class 4.6, ASTM A307 Gr A / B, Class 8.8 / SAE Gr 5 | ASTM A307, A563, ISO 898-1/-2, SAE J429, DIN/ISO dimensional standards |
| Alloy Steel | B7, B16, L7, 4340, A354 BD | ASTM A193 B7/B7M/B16, A194 2H/4, A320 L7, A354 BD, A574, ISO 898-1 10.9/12.9 |
| Duplex Steel | S31803 / S32205, S32304 | ASTM A276, A479, A182 F51/F60, NACE MR0175 / ISO 15156 where specified |
| Super Duplex Steel | S32750, S32760, S32550 | ASTM A276, A479, A182 F53/F55, NACE MR0175 / ISO 15156 where specified |
| Nickel Alloys | Alloy 600 (N06600), Alloy 625 (N06625), Alloy 718 (N07718), Alloy 825 (N08825), Monel 400 (N04400) | ASTM B166, B446, B637, B425, B164, B865, B574, F467/F468 |
| Brass | C26000, C28000, C36000, C46400 | ASTM B16, B21, B134, F467/F468, DIN/ISO dimensional standards |
| Titanium | Grade 1, Grade 2, Grade 5, Grade 9, Grade 12 | ASTM B348, B381, F467/F468, ASME SB-348 |
| High Tensile | Class 8.8, Class 10.9, Class 12.9, SAE Gr 5 / Gr 8 | ISO 898-1/-2, ASTM A193 B7, A354 BD, A325, A490, SAE J429 Gr 5/8 |
General industry information. Availability of a given grade is confirmed at enquiry stage. See individual material pages.
Mechanical Properties
| Property class / grade | Proof stress (MPa) | Mates with |
|---|---|---|
| ISO 898-2 Class 8 | 800 | Class 8.8 bolts |
| ISO 898-2 Class 10 | 1040 | Class 10.9 bolts |
| ISO 898-2 Class 12 | 1150 | Class 12.9 bolts |
| ASTM A194 2H | Per ASTM A194 | ASTM A193 B7 bolts and studs |
| ASTM A194 Gr 8 / 8M | Per ASTM A194 | ASTM A193 B8 / B8M |
| ISO 3506-2 A2-70 / A4-70 | 700 | A2-70 / A4-70 bolts |
Minimum or typical values per cited standards; they vary by grade, diameter, heat treatment and applicable standard.
Surface Finishes
| Finish | Notes |
|---|---|
| Plain | Uncoated; typical for stainless steel and non-ferrous |
| Zinc Plated / Electro Galvanized | Thin zinc layer for indoor and mild environments |
| Hot Dip Galvanized | Thick zinc coating for outdoor and structural use; allowances needed on mating threads |
| Black Oxide | Mild corrosion resistance with oil, low reflectivity |
| Passivated | Removes free iron from stainless steel to restore the passive film |
| Nickel Plated | Corrosion and wear resistance, appearance |
| Customer specified | Other coatings on request |
Manufacturing Process
Typical process route for this product type (general information; actual route depends on size, material and order):
- Bar or wire selection
- Cutting
- Forging or heading
- Tapping
- Heat treatment where required
- Surface treatment
- Inspection and testing
- Marking and packing
Inspection and Testing
- Dimensional inspection against drawing or standard
- Visual and surface inspection
- Thread inspection with go / no-go gauges
- Chemical composition verification and PMI where applicable
- Mechanical testing: tensile, proof load, hardness
- Coating thickness inspection where coated
- Material Test Certificate; EN 10204 3.1 where requested
See the Quality page. Documentation scope is agreed at the quotation stage.
Applications and Industries
Oil & GasPetrochemicalPower GenerationChemical ProcessingConstructionInfrastructureMarine & ShipbuildingHeavy EngineeringFabrication
Packaging
- Cartons or wooden boxes on pallets, selected for weight and destination
- Seaworthy export packing, with corrosion protection where required
- Marking with grade, size and heat or batch number as per order
Customization
Hex Nuts can be quoted to your drawing, sample or specification, including non-standard sizes, lengths, threads, materials and finishes. Send details through the enquiry form.
Frequently Asked Questions
What materials are available for Hex Nuts?
Hex Nuts can be quoted in stainless steel, carbon steel, alloy steel, duplex, super duplex, nickel alloys, brass, titanium and high tensile grades, subject to size and standard.
Which standards can be supplied?
Typical references are ASME B18.2.2, ASTM A194 2H/8/8M, ASTM A563, ISO 4032/4033, DIN 934, ISO 898-2. The governing standard is confirmed against your specification.
What sizes are available?
Size range depends on product, material and standard. Share diameter, length and quantity for confirmation.
Can custom dimensions be manufactured?
Yes, to customer drawing or specification, subject to technical review.
What surface finishes are available?
Plain, zinc plated, hot dip galvanized, black oxide, passivated, electro galvanized, nickel plated or customer specified finishes.
Can material test certificates be supplied?
Material Test Certificates, including EN 10204 3.1 where requested, can be requested with the order. Scope is agreed at quotation.
Related Products
Square Nuts
Square nuts for T-slots, channels and applications needing wrench-resistant seating.
Materials: stainless, carbon, alloy steel and more, subject to enquiry
DIN 557
View Product
Hex Bolts
Hexagon head bolts and cap screws, fully or partially threaded, for general bolted joints in structures, machinery and pressure equipment.
Materials: stainless, carbon, alloy steel and more, subject to enquiry
ASME B18.2.1
View Product
Spring Washers
Helical split washers that provide spring take-up and resistance to loosening under vibration.
Materials: stainless, carbon, alloy steel and more, subject to enquiry
DIN 127 B
View Product
Stud Bolts
Double-ended and fully threaded studs for flanged joints, pressure vessels and heavy equipment.
Materials: stainless, carbon, alloy steel and more, subject to enquiry
ASTM A193 B7/B7M/B16/B8/B8M
View Product